How to Install SPD-SLR Cleats

SHIMANO's new SPD-SLR system brings shoes, cleats, and pedals together for a more direct connection to the bike. A lower stack height, easier pedal engagement, and updated cleat adjustments help riders dial in their setup.

How to Install SHIMANO SPD-SLR Road Bike Cleats

The new cleats and pedals reduce stack height by 2.3 mm compared with the previous system. Pair them with compatible SHIMANO shoes, including the new S-PHYRE RC910 and RC810 road shoes, and the total reduction reaches 2.8 mm.

Cleat adjustment has changed, too. You can still move the cleat side to side to adjust its lateral position. On compatible SPD-SLR shoes, fore-aft adjustment is made using elongated mounting holes in the shoe sole.

SPD-SLR cleats also work with existing SHIMANO SPD-SL road shoes when you choose the appropriate cleat model. For the full benefits of the new system, use SPD-SLR shoes, cleats, and pedals together.

Installing Shimano SPD-SLR Road Bike Cleats

SPD-SLR Cleat Installation at a Glance

  1. Check your shoe's three-bolt mounting holes and choose the compatible SPD-SLR cleat model.
  2. Position the SPD-SLR cleat on the sole.
  3. Install the three cleat bolts.
  4. Provisionally tighten the bolts with a 4 mm hex wrench.
  5. Adjust the lateral position by moving the cleat side to side.
  6. Adjust the fore-aft position using the shoe's mounting holes or the adjustment built into the Gray cleat.
  7. Test engagement and release.
  8. Final-tighten the cleat bolts to 5–6 Nm.

What Do You Need to Install SPD-SLR Cleats?

Before you start, gather the cleats and basic tools you need for installation.

  • A pair of SHIMANO SPD-SLR cleats.
  • Three cleat bolts for each shoe.
  • A 4 mm hex wrench.
  • A torque wrench with a 4 mm hex bit for final tightening.
  • A small amount of appropriate grease for the mounting threads.

For Red (CL-SL100), Yellow (CL-SL110), and Blue (CL-SL120) SPD-SLR cleats, use compatible road shoes with a three-bolt mounting pattern and elongated mounting holes in the sole. These holes provide fore-aft adjustment.

For shoes with round rather than elongated mounting holes, including some older SHIMANO and non-SHIMANO road shoes, use the Gray (CL-SL130) cleat. It has more adjustment built into the cleat itself, though it doesn't provide the same stack-height reduction as the other models.

Shimano RC810 Carbon Sole

Step 1: Position the SPD-SLR Cleat on the Shoe

Turn the cycling shoe over and locate the three cleat mounting points in the sole.

Place the cleat against the sole, aligning its three mounting slots with the threaded holes in the shoe.

SHIMANO SPD-SLR cleats can be used on either the left or right shoe, but the cleat must be oriented correctly with the front of the cleat pointing toward the toe.

Position Shimano SPD-SLR Cleat

Step 2: Install the Cleat Bolts

Insert the three bolts and lightly tighten them with a 4 mm hex wrench. The cleat should stay securely in place while still allowing adjustment.

If you are installing Gray (CL-SL130) cleats, use the included washers.

Do not fully torque the bolts yet.


Step 3: Adjust the Cleat Position

Before fully tightening the bolts, adjust the cleat's side-to-side (lateral) and front-to-back (fore-aft) position to suit your fit.

SHIMANO's technical instructions list approximately the following adjustment ranges at the cleat:

  • 1.5 mm fore-aft.
  • 4.3 mm side-to-side.

Compatible SPD-SLR shoes provide additional fore-aft adjustment through the elongated mounting holes in the sole.

There is no one-size-fits-all cleat position. Foot anatomy, shoe fit, riding position, and personal preference all play a role.

If you are unsure where to start, an experienced bike fitter or bicycle dealer can help establish a position appropriate for your setup.

Adjust Shimano SPD-SLR Cleat Position

Step 4: Test Engagement and Release

With the bolts lightly tightened, practice clipping in and releasing one shoe at a time before final installation.

Use a stationary trainer or a stable support while checking your setup.

Confirm that you can:

  • Engage the cleat normally.
  • Release it with the normal heel-out motion.
  • Pedal without your feet feeling restricted or awkward.
  • Clip in and release consistently with both feet.

If the cleat needs repositioning, loosen the bolts slightly, make a small adjustment, and retest.


Step 5: Tighten SPD-SLR Cleats to the Correct Torque

Once you are satisfied with the cleat position, tighten all three cleat mounting bolts evenly.

SHIMANO specifies a final tightening torque of:

SPD-SLR Cleat Mounting Bolts: 5–6 Nm (43–52 in. lb.)

Use a torque wrench with a 4 mm hex bit rather than tightening only by feel. A small amount of grease on the mounting threads can help reduce the chance of the hardware seizing over time.

Tightening Shimano SPD-SLR Cleat Bolts

How Tight Should SPD-SLR Cleat Bolts Be?

The bolts must hold the cleat securely without being overtightened.

Following the specified 5–6 Nm torque range provides a repeatable way to secure the cleat without relying on guesswork.

After installation, periodically inspect the bolts and cleat for looseness or wear as part of normal bicycle maintenance.


How Do You Know if Your SPD-SLR Cleat Position Is Right?

A good cleat position lets you pedal comfortably and clip in and out consistently, without forcing your feet into an awkward position.

Avoid forcing your feet or knees into a particular alignment based on a generic fit guide. If you experience ongoing discomfort or struggle to find a comfortable position, consider a professional bike fit.

Shimano DURA-ACE R9300 SPD-SLR pedals

Are All SPD-SLR Cleats Installed the Same Way?

Red, Yellow, and Blue SPD-SLR cleats use the same three-bolt mounting interface and are intended for compatible shoes with elongated mounting holes. Gray SPD-SLR cleats have additional adjustment built in, making them suitable for three-bolt road shoes with round mounting holes, including some older SHIMANO and non-SHIMANO models.

Each cleat model also offers a different amount or type of float, which is the rotational movement available while clipped into the pedal. Installation is similar across models, but the float you choose affects how freely your foot can rotate.

Cleat float and cleat position are separate adjustments, so choosing a different cleat does not replace the need to position it correctly on the shoe.

Shimano SPD-SLR road bike cleats

SPD-SLR Cleat Installation Checklist

  • Check that your shoes have elongated three-bolt mounting holes for Red, Yellow, or Blue SPD-SLR cleats, or use Gray cleats with compatible three-bolt shoes that have round mounting holes.
  • Orient the cleat correctly.
  • Install three bolts (and washers for Gray cleats).
  • Provisionally tighten before final positioning.
  • Adjust fore-aft and lateral position as needed.
  • Practice clipping in and releasing before riding.
  • Final-tighten all bolts to 5–6 Nm.
  • Recheck the installation periodically for looseness or wear.

Once the cleats are positioned comfortably and all bolts are tightened to the specified torque, your shoes are ready to use with compatible SHIMANO SPD-SLR pedals.